Need some info on building a propper 2l bottom end
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Need some info on building a propper 2l bottom end
Hi guys hope you all doing well!
I want to upgrade on my caddy's 2l 8v bottom end. Stil stock standard at this stage. I heard some one saying 2.3 caravelle pistons wil make a huge differance but not sure if it is the right way to go. Any guidens would be highly appriciated. Running on 282 estas cam with dicktator management and the std bottom now. Keep in mind it is my daily driver.
Thanks in advance!
Sent from my SM-G920F using Tapatalk
I want to upgrade on my caddy's 2l 8v bottom end. Stil stock standard at this stage. I heard some one saying 2.3 caravelle pistons wil make a huge differance but not sure if it is the right way to go. Any guidens would be highly appriciated. Running on 282 estas cam with dicktator management and the std bottom now. Keep in mind it is my daily driver.
Thanks in advance!
Sent from my SM-G920F using Tapatalk
- chucker02
- Captain
- Posts: 2966
- Registered for: 11 years 3 months
- Car Make: VW
- Car Model: Citi ADY
- Location: Bloemfontein
Re: Need some info on building a propper 2l bottom end
Build a 2.1 with a tdi crank, heard that it makes the most difference and adds alot of torque.
Current:
2006 Citi Golf 2E, Dictator, 4-2-1
Ex:
2003 Audi A3 1.8t, Thanas Tuned, FMIC, coilies, DP and exhaust
2007 Citi golf. ADY with Spitronics 60-2, estas 282, 4-2-1, coilies
Rides thread: http://vwclub.co.za/forum/viewtopic.php?f=11&t=183329
2002 Citi golf. ADY carb, estas 282, 4-2-1, GW delarey big brake kit.
Rides thread: http://vwclub.co.za/forum/viewtopic.php?f=11&t=157603
1971 VW beetle
2006 Citi Golf 2E, Dictator, 4-2-1
Ex:
2003 Audi A3 1.8t, Thanas Tuned, FMIC, coilies, DP and exhaust
2007 Citi golf. ADY with Spitronics 60-2, estas 282, 4-2-1, coilies
Rides thread: http://vwclub.co.za/forum/viewtopic.php?f=11&t=183329
2002 Citi golf. ADY carb, estas 282, 4-2-1, GW delarey big brake kit.
Rides thread: http://vwclub.co.za/forum/viewtopic.php?f=11&t=157603
1971 VW beetle
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
So I need the 1.9 tdi crank for that and whet pistons do I need?chucker02 wrote:Build a 2.1 with a tdi crank, heard that it makes the most difference and adds alot of torque.
Sent from my SM-G920F using Tapatalk
- PapaJo
- Brigadier
- Posts: 6990
- Registered for: 14 years
- Car Make: VW's
- Car Model: '16 7R, '86 Caddy AUM 20VT
- Membership No: missing
- Location: Meyerton or Offshore Guyana.
Re: Need some info on building a propper 2l bottom end
The std 2l bottom end is strong enough if you want 2l.
Focus on the head to get more power. You did not state any orher mods to head apart from 282 estas cam. A port and flow with work done to the valves and branch would free up more ponies. If you decide to skim the head to increase compression, don't skim morr than 0.5 mm from std or you may need to add fuel additives.
Other than that, chucker02 has said you can go for a 2.1l motor and still need to do supporting mods to the head to get the most out of the motor and not just by fitting a cam.
Search around on the forum and you will find more info regarding such a conversion. CA18 nissan pistons are used, but only on 16v conversions as the 16v head has a larger combustion chamber. Afaik a bmw piston can be used for a 8v 2.1l conversion, but can't recall which one. Get in touch with Torker here on the forum or Sarel 8v performance. They should be able to give you the correct info.
Focus on the head to get more power. You did not state any orher mods to head apart from 282 estas cam. A port and flow with work done to the valves and branch would free up more ponies. If you decide to skim the head to increase compression, don't skim morr than 0.5 mm from std or you may need to add fuel additives.
Other than that, chucker02 has said you can go for a 2.1l motor and still need to do supporting mods to the head to get the most out of the motor and not just by fitting a cam.
Search around on the forum and you will find more info regarding such a conversion. CA18 nissan pistons are used, but only on 16v conversions as the 16v head has a larger combustion chamber. Afaik a bmw piston can be used for a 8v 2.1l conversion, but can't recall which one. Get in touch with Torker here on the forum or Sarel 8v performance. They should be able to give you the correct info.
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
Thanks for the advice! I will do some home work and go from there.PapaJo wrote:The std 2l bottom end is strong enough if you want 2l.
Focus on the head to get more power. You did not state any orher mods to head apart from 282 estas cam. A port and flow with work done to the valves and branch would free up more ponies. If you decide to skim the head to increase compression, don't skim morr than 0.5 mm from std or you may need to add fuel additives.
Other than that, chucker02 has said you can go for a 2.1l motor and still need to do supporting mods to the head to get the most out of the motor and not just by fitting a cam.
Search around on the forum and you will find more info regarding such a conversion. CA18 nissan pistons are used, but only on 16v conversions as the 16v head has a larger combustion chamber. Afaik a bmw piston can be used for a 8v 2.1l conversion, but can't recall which one. Get in touch with Torker here on the forum or Sarel 8v performance. They should be able to give you the correct info.
Sent from my SM-G920F using Tapatalk
-
- Cadet
- Posts: 211
- Registered for: 7 years
- Car Make: Isuzu
- Car Model: KB250 LE 2006
- Location: benoni gauteng
Re: Need some info on building a propper 2l bottom end
I've been looking at a bunch of different conversions lately and Apparently this mod eats bearings , but I'm by no means an expert just giving a heads up .chucker02 wrote:Build a 2.1 with a tdi crank, heard that it makes the most difference and adds alot of torque.
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
I spoke to Nellis today and he has head which was done by Mike Dixon and from some of my connectons and was told it will be a wise choice to go for it. As far as the bottom end, it will be on hold for now.
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
I picked up another bugger-up today. When driving at 200km/h for about 50km the engin pushes a bit of oil out at the breather, is this normal on these 2l engins or where should I look for the cause?
I fitted new rings and big-ends and did propper honing on the sleeves. There was no ridge on the sleeves and drove gently for the first 1000km befor doing the dyno. Motor engineering did the head and messed it up so they gave me a 1.6 head which I had to reem the intake in order for the injectors not to squirt against the head. The valve stems was replaced but not the guids. Could this also cause the engin to breath as much?
Above all there is no problem with power or excelleration.
Sent from my SM-G920F using Tapatalk
I fitted new rings and big-ends and did propper honing on the sleeves. There was no ridge on the sleeves and drove gently for the first 1000km befor doing the dyno. Motor engineering did the head and messed it up so they gave me a 1.6 head which I had to reem the intake in order for the injectors not to squirt against the head. The valve stems was replaced but not the guids. Could this also cause the engin to breath as much?
Above all there is no problem with power or excelleration.
Sent from my SM-G920F using Tapatalk
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
By the way! Thanks for all the advice and support so far, nice to get some honest opinions from guys with experience on these engins.
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk
- PapaJo
- Brigadier
- Posts: 6990
- Registered for: 14 years
- Car Make: VW's
- Car Model: '16 7R, '86 Caddy AUM 20VT
- Membership No: missing
- Location: Meyerton or Offshore Guyana.
Re: Need some info on building a propper 2l bottom end
When motor was assembled, did you install the plastic oil splash cover that fit over the cam below the tappet cover?
How is the breather on the block connected? Going to an oil catch tank with breather filter on?
How is the breather on the block connected? Going to an oil catch tank with breather filter on?
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
Northern cape postmasburg, no cops around except in December around Christmas. The bottom breather is blanked of and on top only the filter. Yes the splashplate in the top is in place! No oul catch tank fitted yet, howeve I did order one.
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk
-
- Cadet
- Posts: 815
- Registered for: 17 years 8 months
- Location: Bloemfontein
Re: Need some info on building a propper 2l bottom end
What happens if you unblock the bottom breather? Things are put there by the engineers for a reason.The bottom breather is blanked of and on top only the filter
My cars: 2004 Nissan Almera 1.6
1977 Datsun 1200GX
(100% FULLY restored, 13" mags fitted)
Wife's car: 2019 Suzuki Ciaz
1977 Datsun 1200GX
(100% FULLY restored, 13" mags fitted)
Wife's car: 2019 Suzuki Ciaz
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
It gets worse!
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
But below 5k rpm no problems! Only when driving at very high rpm for a period of time.
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk
-
- Cadet
- Posts: 815
- Registered for: 17 years 8 months
- Location: Bloemfontein
Re: Need some info on building a propper 2l bottom end
I'm no expert. Lets wait for the experts to comment but that sounds like a ring seal problem at high revs/high pressure.
How many km on the block?
How many km on the block?
My cars: 2004 Nissan Almera 1.6
1977 Datsun 1200GX
(100% FULLY restored, 13" mags fitted)
Wife's car: 2019 Suzuki Ciaz
1977 Datsun 1200GX
(100% FULLY restored, 13" mags fitted)
Wife's car: 2019 Suzuki Ciaz
- vadia
- Cadet
- Posts: 88
- Registered for: 7 years 7 months
- Car Make: vw,nissan,merc
- Car Model: mk1,np300,c200 amg,gti7
- Location: randburg
Re: Need some info on building a propper 2l bottom end
hi when i cracked my no1 piston on my 1.8 afv block rebored 20thou it pissed oil out off both breathers and it was turbo charged
opel monza cd
ford xr3i
mazda 626 200i egi
ford bantam
vw beach buggy
vw mk1 2.0 8v turbo
ford xr3i
mazda 626 200i egi
ford bantam
vw beach buggy
vw mk1 2.0 8v turbo
- 104bpm
- Enlisted
- Posts: 18
- Registered for: 8 years
- Car Make: VW
- Car Model: '98 Golf 1
- Location: Durban
Re: Need some info on building a propper 2l bottom end
Lmao!THANAS wrote:More importantly where do you live that you can do 200 kph for 50 kms?
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
Not sure. Bought it with the block.
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk
- PapaJo
- Brigadier
- Posts: 6990
- Registered for: 14 years
- Car Make: VW's
- Car Model: '16 7R, '86 Caddy AUM 20VT
- Membership No: missing
- Location: Meyerton or Offshore Guyana.
Re: Need some info on building a propper 2l bottom end
Open that bottom breather. It is ther for a reason.corney wrote:Northern cape postmasburg, no cops around except in December around Christmas. The bottom breather is blanked of and on top only the filter. Yes the splashplate in the top is in place! No oul catch tank fitted yet, howeve I did order one.
Sent from my SM-G920F using Tapatalk
- PapaJo
- Brigadier
- Posts: 6990
- Registered for: 14 years
- Car Make: VW's
- Car Model: '16 7R, '86 Caddy AUM 20VT
- Membership No: missing
- Location: Meyerton or Offshore Guyana.
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
Nope, decided to gather all the parts and then rebuild the whole engin from top to bottom. Rebore, cut crank, blueprint and get a head from Mike dixon. I believe that is the surest way to make sure it runs perfect.
Any sugestions on who does propper porting and flowing? I heard Mike Dixon does a great job on the vw heads. Don't want to make another mistake
Sent from my SM-G920F using Tapatalk
Any sugestions on who does propper porting and flowing? I heard Mike Dixon does a great job on the vw heads. Don't want to make another mistake
Sent from my SM-G920F using Tapatalk
- panic-mechanic
- Panic's Place
- Posts: 26715
- Registered for: 21 years 8 months
- Membership No: 79
- Location: Benoni, putfontein.
Re: Need some info on building a propper 2l bottom end
The breather is the only issue and yes all engines will breathe when you work them that hard. It is pretty normal.
Open the bottom breather, put it into a bottle and empty it out now and then.
Open the bottom breather, put it into a bottle and empty it out now and then.
Stephan van Tonder - Jhb - Putfontein Benoni
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10
Perfect Power dealer. I do dyno tuning.
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10
Perfect Power dealer. I do dyno tuning.
-
- Cadet
- Posts: 65
- Registered for: 7 years 3 months
Re: Need some info on building a propper 2l bottom end
Will try it and give you feedback on the results. Thanks for the advice!
Sent from my SM-G920F using Tapatalk
Sent from my SM-G920F using Tapatalk