mp 9 wiring diagram please

vdubs4life
Cadet
Posts: 84
Registered for: 15 years 7 months
Car Make: mazda 6
Car Model: mps
Membership No: missing
Location: jhb

mp 9 wiring diagram please

Post by vdubs4life »

hi there people does anybody know where i can get a wiring diagram for mp9
or if anybody knows if the injectors are polarity sensitive or not ?
User avatar
panic-mechanic
Panic's Place
Posts: 26715
Registered for: 21 years 7 months
Membership No: 79
Location: Benoni, putfontein.

Re: mp 9 wiring diagram please

Post by panic-mechanic »

Injectors are not polarity sensitive no. But if you have a piece of the wiring harness you will see there is one wire that is common to them all. That one is the 12v+
If you just search or look back about a week - somebody posted the mp9 pinout diagram.
Stephan van Tonder - Jhb - Putfontein Benoni
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10

Perfect Power dealer. I do dyno tuning.
vdubs4life
Cadet
Posts: 84
Registered for: 15 years 7 months
Car Make: mazda 6
Car Model: mps
Membership No: missing
Location: jhb

Re: mp 9 wiring diagram please

Post by vdubs4life »

thanks alot panic ill check back for those pinouts
User avatar
amstel18
Lieutenant-Colonel
Posts: 4834
Registered for: 16 years 3 months
Car Make: VW
Car Model: Tiguan Allspace
Membership No: missing
Location: Brackenfell, Cape Town

Re: mp 9 wiring diagram please

Post by amstel18 »

Here you go:

MP9.0 Pinouts for TiiCo ECU.
1 Ground
2 Throttle body 1
3 NC
4 Injector 4
5 NC
6 Injector 2
7 Injector 1
8 Phase sensor +5V
9 RPM signal ------------------>Rev counter
10 Throttle body 3
11 GND
12 NC
13 Phase sensor signal
14 Throttle body 4
15 NC
16 Throttle body 8
17 GND
18 TMAP 4
19 Knock sensor 2
20 NC
21 Batt 12V
22 NC
23 GND
24 Ignition Control unit
25 Fuel pump relay-------------> Fuel pump switching relay
26 Throttle body 2
27 NC
28 Inj 3
29 Diag K-Line ----------------> to pin 7 on the diagnostic port
30 NC
31 NC
32 NC
33 NC
34 NC
35 AC
36 Vehicle speed input --------> From speed sensor
37 TMAP 3
38 O2 Data --------------------> Oxygen sensor (Exhaust)
39 Knock sensor 1
40 NC
41 Throttle body 5
42 Engine Coolant sensor
43 TMAP 2
44 NC
45 Screen for Phase and Knock sensor wires.
Current:
2022 GWM P-Series LT 4x4
Ex:
2018 VW Tiguan Allspace
2013 Audi A3 Sportback 1.8 TFSI S-Tronic
2015 Pure White 1.2tsi Comfortline
2011 2L BiTdi ROK D/C Highline
2006 Seat Ibiza Cupra TDI
91 Caddy, ADY motor on mp9, wildcat 4-1 branch and 50mm Evolution s/s exhaust
96 1600 Chico (sold)
vdubs4life
Cadet
Posts: 84
Registered for: 15 years 7 months
Car Make: mazda 6
Car Model: mps
Membership No: missing
Location: jhb

Re: mp 9 wiring diagram please

Post by vdubs4life »

thanks for the help guys the only thing is the gotech wants three wires for tps and mp9 pinouts just say throttle 1 4 5 which of these is signal which is negative and same goes with distributor and then the idling sensor cause mp9 has like 8 wires to each of these sensors oh and same with water temp
User avatar
panic-mechanic
Panic's Place
Posts: 26715
Registered for: 21 years 7 months
Membership No: 79
Location: Benoni, putfontein.

Re: mp 9 wiring diagram please

Post by panic-mechanic »

Uhm - WTF does gotech feature now all of a sudden. You were asking for a wiring diagram for MP9 yes?.
Stephan van Tonder - Jhb - Putfontein Benoni
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10

Perfect Power dealer. I do dyno tuning.
vdubs4life
Cadet
Posts: 84
Registered for: 15 years 7 months
Car Make: mazda 6
Car Model: mps
Membership No: missing
Location: jhb

Re: mp 9 wiring diagram please

Post by vdubs4life »

Cause im changing from mp9 to gotech if i know the outputs of mp9 then ill know what must connect where on the gotech correct me if im wrong im trying to figure this out
Torker
General
Posts: 9591
Registered for: 18 years
Car Make: VW
Car Model: Golf GT
Membership No: 1464
Location: Springs

Re: mp 9 wiring diagram please

Post by Torker »

vdubs4life wrote:Cause im changing from mp9 to gotech if i know the outputs of mp9 then ill know what must connect where on the gotech correct me if im wrong im trying to figure this out
Basically the same as what I want to do except I'm going with Dicktator.

PS - Mail sent...
Current rides:

VW Golf - 83 GT 2.1 16V 2-door with throttles
VW Golf - 78 LS 2.0 8V 4-door (2.1 ABF with throttles in progress)
VW Golf - '08 Citi Storm - 1.4 for now
Hyundai - 1.4 Getz (daily)
vdubs4life
Cadet
Posts: 84
Registered for: 15 years 7 months
Car Make: mazda 6
Car Model: mps
Membership No: missing
Location: jhb

Re: mp 9 wiring diagram please

Post by vdubs4life »

nobody know where to get this diagram
UDC
Colonel
Posts: 5738
Registered for: 17 years 2 months
Membership No: 1041
Location: Durban

Re: mp 9 wiring diagram please

Post by UDC »

Image
User avatar
MhVW
Lieutenant
Posts: 1708
Registered for: 14 years 7 months
Car Make: Volkswagen
Car Model: '06 Polo Classic 1.9 TDi
Membership No: 1466
Location: Cape Town

Re: mp 9 wiring diagram please

Post by MhVW »

Ok, I'm trying to wire up my EFI management to the MP9 throttle body.

I need to connect the TPS signals to pins 4 - earth, 5 - signal and 7 - 5V. As per the diagram above.
Only problem, I don't know which pin is which on the connector on the MP9 throttle body.

Could anyone assist with a diagram indicating the pin numbering on the MP9 throttle body.
| 2006 VW Polo Classic 1.9TDi ...Tow Car... | ? ? ? ? ? ? ...Weekend Warrior... | 2005 Honda CBX250 Twister ...Daily... |
Torker
General
Posts: 9591
Registered for: 18 years
Car Make: VW
Car Model: Golf GT
Membership No: 1464
Location: Springs

Re: mp 9 wiring diagram please

Post by Torker »

Here's the diagram I used when wiring my Dicktator, the MP9 part should be the same...

Image
Current rides:

VW Golf - 83 GT 2.1 16V 2-door with throttles
VW Golf - 78 LS 2.0 8V 4-door (2.1 ABF with throttles in progress)
VW Golf - '08 Citi Storm - 1.4 for now
Hyundai - 1.4 Getz (daily)
User avatar
MhVW
Lieutenant
Posts: 1708
Registered for: 14 years 7 months
Car Make: Volkswagen
Car Model: '06 Polo Classic 1.9 TDi
Membership No: 1466
Location: Cape Town

Re: mp 9 wiring diagram please

Post by MhVW »

I'm actually looking for a diagram showing the pin locations on the MP9 throttle body, the one with the stepper motor.
MhVW wrote:I need to connect the TPS signals to pins 4 - earth, 5 - signal and 7 - 5V. As per the diagram above.
Only problem, I don't know which pin is which on the connector on the MP9 throttle body.

Could anyone assist with a diagram indicating the pin numbering on the MP9 throttle body.
| 2006 VW Polo Classic 1.9TDi ...Tow Car... | ? ? ? ? ? ? ...Weekend Warrior... | 2005 Honda CBX250 Twister ...Daily... |
Torker
General
Posts: 9591
Registered for: 18 years
Car Make: VW
Car Model: Golf GT
Membership No: 1464
Location: Springs

Re: mp 9 wiring diagram please

Post by Torker »

MhVW wrote:I'm actually looking for a diagram showing the pin locations on the MP9 throttle body, the one with the stepper motor.
MhVW wrote:I need to connect the TPS signals to pins 4 - earth, 5 - signal and 7 - 5V. As per the diagram above.
Only problem, I don't know which pin is which on the connector on the MP9 throttle body.

Could anyone assist with a diagram indicating the pin numbering on the MP9 throttle body.

Top tip - You'll see I've included the MP9 wire colors as well so if you put in a bit of effort you'll be able to see which pin goes where...
Current rides:

VW Golf - 83 GT 2.1 16V 2-door with throttles
VW Golf - 78 LS 2.0 8V 4-door (2.1 ABF with throttles in progress)
VW Golf - '08 Citi Storm - 1.4 for now
Hyundai - 1.4 Getz (daily)
User avatar
MhVW
Lieutenant
Posts: 1708
Registered for: 14 years 7 months
Car Make: Volkswagen
Car Model: '06 Polo Classic 1.9 TDi
Membership No: 1466
Location: Cape Town

Re: mp 9 wiring diagram please

Post by MhVW »

Torker wrote:Top tip - You'll see I've included the MP9 wire colors as well so if you put in a bit of effort you'll be able to see which pin goes where...
Thanx for the top tip, but I never mentioned that I've got a harness... :bang: :bang: :bang:
Rendering your top tip useless... :bang: :bang: :bang:

I've got no plug nor wiring as as referernce, thus the need for the pin locations on the MP9 throttle body.

Need to solder the wires to the throttle body until I can do it properly. :crazy:
| 2006 VW Polo Classic 1.9TDi ...Tow Car... | ? ? ? ? ? ? ...Weekend Warrior... | 2005 Honda CBX250 Twister ...Daily... |
Torker
General
Posts: 9591
Registered for: 18 years
Car Make: VW
Car Model: Golf GT
Membership No: 1464
Location: Springs

Re: mp 9 wiring diagram please

Post by Torker »

MhVW wrote:
Torker wrote:Top tip - You'll see I've included the MP9 wire colors as well so if you put in a bit of effort you'll be able to see which pin goes where...
Thanx for the top tip, but I never mentioned that I've got a harness... :bang: :bang: :bang:
Rendering your top tip useless... :bang: :bang: :bang:

I've got no plug nor wiring as as referernce, thus the need for the pin locations on the MP9 throttle body.

Need to solder the wires to the throttle body until I can do it properly. :crazy:
You know what, I've got all the info you need but you can seeing that you've got that sort of an attitude with somebody that is trying to help you, you can get stuffed... :moon:
Current rides:

VW Golf - 83 GT 2.1 16V 2-door with throttles
VW Golf - 78 LS 2.0 8V 4-door (2.1 ABF with throttles in progress)
VW Golf - '08 Citi Storm - 1.4 for now
Hyundai - 1.4 Getz (daily)
User avatar
VWicked
Lieutenant-General
Posts: 8576
Registered for: 14 years 7 months
Car Make: VW
Car Model: Golf 2 GTi
Membership No: 1492
Location: Midrand

Re: mp 9 wiring diagram please

Post by VWicked »

What i did was remove the whole mp9 harness,comp box and sell (easily get R 1000 for it). Keep injector harness and get a tp100 wiring harness from GW for R 150 or so, and wire it like the dicktator/(gotech) manual tells you to. Much easier and you get some money back!!
Have you had your bottle of Hatorade today?

1992 Golf Mk2 GTi VR6
1994 Caddy 1800 Sport
User avatar
MhVW
Lieutenant
Posts: 1708
Registered for: 14 years 7 months
Car Make: Volkswagen
Car Model: '06 Polo Classic 1.9 TDi
Membership No: 1466
Location: Cape Town

Re: mp 9 wiring diagram please

Post by MhVW »

Torker wrote:You know what, I've got all the info you need but you can seeing that you've got that sort of an attitude with somebody that is trying to help you, you can get stuffed... :moon:
Excuse my ignorance, but would you please care to explain how your table would be of any help.

You're referencing MP9 ECU pin-outs, associated wire color codes and function with the wire color codes and pin-outs of the Dicktator EFI unit.

I don't have any MP9 wiring on the car. It's originaly a carb model. Further more I don't have the MP9 throttle body plug or part of the harness. I only have the MP9 throttle body and my management.
| 2006 VW Polo Classic 1.9TDi ...Tow Car... | ? ? ? ? ? ? ...Weekend Warrior... | 2005 Honda CBX250 Twister ...Daily... |
User avatar
graham savage
Colonel
Posts: 5035
Registered for: 18 years 5 months
Car Make: VW
Car Model: Caddy's, Mk2's, Mk4, Ford etc
Membership No: 803
Location: Johannesburg
Contact:

Re: mp 9 wiring diagram please

Post by graham savage »

MhVW wrote:
Torker wrote:You know what, I've got all the info you need but you can seeing that you've got that sort of an attitude with somebody that is trying to help you, you can get stuffed... :moon:
Excuse my ignorance, but would you please care to explain how your table would be of any help.

You're referencing MP9 ECU pin-outs, associated wire color codes and function with the wire color codes and pin-outs of the Dicktator EFI unit.

I don't have any MP9 wiring on the car. It's originaly a carb model. Further more I don't have the MP9 throttle body plug or part of the harness. I only have the MP9 throttle body and my management.
Then Why be asking for a MP9 diagram? You have nothing MP9 but ask for MP9 info??? Ask for help wiring slotech onto MP9 throttle body... give the right info in the beginning and get the right info in the end... how must we know what you have or have not?

Better yet, seeing as though you are such a clever ****, why not measure the resistance/voltages on the TB like it tells you to do in the slotech manual, All you are looking for is the TPS signal... WHICH you don't really need but then again who's to say you have a multimeter or know how to use it?
Quik-Trix
Lieutenant
Posts: 1405
Registered for: 15 years 7 months
Car Make: VW
Car Model: '84 Mk1 2.0 20v ITB's
Membership No: 3004
Location: Durban

Re: mp 9 wiring diagram please

Post by Quik-Trix »

MhVW wrote: Could anyone assist with a diagram indicating the pin numbering on the MP9 throttle body.
Maybe this might help

Image
User avatar
MhVW
Lieutenant
Posts: 1708
Registered for: 14 years 7 months
Car Make: Volkswagen
Car Model: '06 Polo Classic 1.9 TDi
Membership No: 1466
Location: Cape Town

Re: mp 9 wiring diagram please

Post by MhVW »

Quik-Trix wrote:
MhVW wrote: Could anyone assist with a diagram indicating the pin numbering on the MP9 throttle body.
Maybe this might help

*snip*
Thanx, Quik-Trix

That's exactly what I asked for from the start.

I've already managed to figure it out, but this is a good illustration of the pin numbering on the MP9 throttle body.
| 2006 VW Polo Classic 1.9TDi ...Tow Car... | ? ? ? ? ? ? ...Weekend Warrior... | 2005 Honda CBX250 Twister ...Daily... |
User avatar
panic-mechanic
Panic's Place
Posts: 26715
Registered for: 21 years 7 months
Membership No: 79
Location: Benoni, putfontein.

Re: mp 9 wiring diagram please

Post by panic-mechanic »

5,7,8 is the tps wires.
Stephan van Tonder - Jhb - Putfontein Benoni
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10

Perfect Power dealer. I do dyno tuning.
User avatar
MhVW
Lieutenant
Posts: 1708
Registered for: 14 years 7 months
Car Make: Volkswagen
Car Model: '06 Polo Classic 1.9 TDi
Membership No: 1466
Location: Cape Town

Re: mp 9 wiring diagram please

Post by MhVW »

panic-mechanic wrote:5,7,8 is the tps wires.
According to the table posted earlier pin-8 is the "closed throttle position switch" and the Gotech wiring diagram before that indicates TPS on pins-4,5,7.

I picked up the TPS on 4,5,7.

But will go test to pin-8 as well, could've made a mistake.
| 2006 VW Polo Classic 1.9TDi ...Tow Car... | ? ? ? ? ? ? ...Weekend Warrior... | 2005 Honda CBX250 Twister ...Daily... |
User avatar
panic-mechanic
Panic's Place
Posts: 26715
Registered for: 21 years 7 months
Membership No: 79
Location: Benoni, putfontein.

Re: mp 9 wiring diagram please

Post by panic-mechanic »

I have seen the guys use 4,5,7. It really is only one of the common earths that change. 5,7 is the pins with the resistance over it. The other is 'ground'.
Stephan van Tonder - Jhb - Putfontein Benoni
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10

Perfect Power dealer. I do dyno tuning.
User avatar
MhVW
Lieutenant
Posts: 1708
Registered for: 14 years 7 months
Car Make: Volkswagen
Car Model: '06 Polo Classic 1.9 TDi
Membership No: 1466
Location: Cape Town

Re: mp 9 wiring diagram please

Post by MhVW »

panic-mechanic wrote:I have seen the guys use 4,5,7. It really is only one of the common earths that change. 5,7 is the pins with the resistance over it. The other is 'ground'.
Thanx, will check it out for interest sake.
| 2006 VW Polo Classic 1.9TDi ...Tow Car... | ? ? ? ? ? ? ...Weekend Warrior... | 2005 Honda CBX250 Twister ...Daily... |
Post Reply