7 speed Dsg DQ200 BASIC SETTINGS
-
kingozzi
- Enlisted
- Posts: 40
- Registered for: 6 years 8 months
- Car Make: Vw
- Car Model: PGTI1.4tsi 172kw 309nm(crank)
7 speed Dsg DQ200 BASIC SETTINGS
Good day fellas. I have a problem that Google can't help me with, I'm working on a 1.4 tsi jetta with dsg DQ200 box! Done a clutch replacement and now when doing basic settings on the 1st stage (engine on not running) it shows 255 101 0, It should be showing 4 0 0 meaning I can move on to stage 2 (engin running) the mechatronics wasn't touched the breath was blocked no oil leakd out or anything like that..
-
Baldwin02002
- Cadet
- Posts: 356
- Registered for: 15 years 8 months
- Car Make: VW
- Car Model: Mk2 GTS
- Membership No: missing
- Location: Mulbarton
Re: 7 speed Dsg DQ200 BASIC SETTINGS
Try this http://wiki.ross-tech.com/wiki/index.ph ... ic_Setting
Otherwise start the car and let it idle for few minutes to warm up an oil. Hold a brake pedal and change gears for couple of times from Park - Drive - Neutral - Reverse.
Below are the procedures for 6 speed DSG and dont think will work:
Clutch Adaptation
Control Module Software Version < 0800:
Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Special notes.
When found in the early software level (0627/0628) (8N) Audi TT:
Basic Settings group 062 may take several minutes to complete. The final values may report: [18 | 18 | .285 | .24] and Basic Settings will report ON when finished.
If Basic Settings group 062 reports ERROR:| Group 062| Not | Available try test driving the vehicle and repeating at normal operating temp.
Internal Ref: ST?ID=66725 and E?ID=309867
Control Module Software Version >= 0800 :
Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Clutch Safety Function)
Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Pressure Adaptation)
Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Steering Wheel Paddle Installation)
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Otherwise start the car and let it idle for few minutes to warm up an oil. Hold a brake pedal and change gears for couple of times from Park - Drive - Neutral - Reverse.
Below are the procedures for 6 speed DSG and dont think will work:
Clutch Adaptation
Control Module Software Version < 0800:
Group 062
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Special notes.
When found in the early software level (0627/0628) (8N) Audi TT:
Basic Settings group 062 may take several minutes to complete. The final values may report: [18 | 18 | .285 | .24] and Basic Settings will report ON when finished.
If Basic Settings group 062 reports ERROR:| Group 062| Not | Available try test driving the vehicle and repeating at normal operating temp.
Internal Ref: ST?ID=66725 and E?ID=309867
Control Module Software Version >= 0800 :
Group 067
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Clutch Safety Function)
Group 068
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Pressure Adaptation)
Group 065
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Reset Values (Steering Wheel Paddle Installation)
Group 063
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
Current:
Mk2 GTS 1.8 --> 2.0 16v MP9 --> Soon to be 2.1 16v MP9 with Throttles
S3 2003 BAM --> Stage 1 with full Exhaust
S4 2004 --> Stock
A3 2010 1.8T Cabrio --> Stock
//////
Previous
Golf Citi 2.0 8v MP9 2007
Jetta 4 V5 10V
Honda CB400 '74
Mk2 GTS 1.8 --> 2.0 16v MP9 --> Soon to be 2.1 16v MP9 with Throttles
S3 2003 BAM --> Stage 1 with full Exhaust
S4 2004 --> Stock
A3 2010 1.8T Cabrio --> Stock
//////
Previous
Golf Citi 2.0 8v MP9 2007
Jetta 4 V5 10V
Honda CB400 '74
-
Nikosblitz
- Enlisted
- Posts: 1
- Registered for: 2 hours 56 minutes
Re: 7 speed Dsg DQ200 BASIC SETTINGS
Hello, I have problems with mine dq200 surprise surprise..
New clutch pack and whole kit, repaird tcu worked fine..
When I installed the new clutch kit it was working and driving very good smooth shifts no problems,
I decided to do basic settings on the transmission it goes thru and completes with code ( 254.0.0)
But after it was done when I put it in D loud bang is heard from around clutch also when brake is realesed the car jurks forward or stalls and throws a P177D clutch torque too high, but it shifts almost normal with little jerks after you start moving from 1st gear, also Reverse is smooth from the start no bangings or jerks..
PLEASE HELP.. IM DESPERATE..
THANKS
New clutch pack and whole kit, repaird tcu worked fine..
When I installed the new clutch kit it was working and driving very good smooth shifts no problems,
I decided to do basic settings on the transmission it goes thru and completes with code ( 254.0.0)
But after it was done when I put it in D loud bang is heard from around clutch also when brake is realesed the car jurks forward or stalls and throws a P177D clutch torque too high, but it shifts almost normal with little jerks after you start moving from 1st gear, also Reverse is smooth from the start no bangings or jerks..
PLEASE HELP.. IM DESPERATE..
THANKS