Hi,
I need some advice here with the alignment of the timing belt pulley on the crankshaf.
This is a FSI crankshat and the nose was machined down to accommodate the pulley from the 8V motors.
The pulley sticks out by 2mm over the intermediate shaft pulley.
Can anyone confirm this?
Timing belt crank pulley alignement
- vandyh
- Cadet
- Posts: 93
- Registered for: 10 years 4 months
- Car Make: VW
- Car Model: Velociti
- Location: Boksburg
Timing belt crank pulley alignement
Current ride
2007 - Jetta VI 2.0TDI
2007 - Velociti - 2.0 (91wkW, 174nm) @ 8V Performance
2014 - Kia Rio TEC
Previous rides
2008 - Polo 1.9 TDi 14i
2008 - Citi 14i
1996 - Citi Chico
2003 - Ford Fiesta
1986 - Golf MK2
2007 - Jetta VI 2.0TDI
2007 - Velociti - 2.0 (91wkW, 174nm) @ 8V Performance
2014 - Kia Rio TEC
Previous rides
2008 - Polo 1.9 TDi 14i
2008 - Citi 14i
1996 - Citi Chico
2003 - Ford Fiesta
1986 - Golf MK2
- panic-mechanic
- Panic's Place
- Posts: 26715
- Registered for: 21 years 7 months
- Membership No: 79
- Location: Benoni, putfontein.
Re: Timing belt crank pulley alignement
Well that is subject to all kinds of parallax error but take a long straigh edge or ruler and hold it against the intermediate shaft pully and over the timing gear then you can confirm and even measure it yourself without asking for confirmation from a picture.
Stephan van Tonder - Jhb - Putfontein Benoni
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10
Perfect Power dealer. I do dyno tuning.
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10
Perfect Power dealer. I do dyno tuning.
- vandyh
- Cadet
- Posts: 93
- Registered for: 10 years 4 months
- Car Make: VW
- Car Model: Velociti
- Location: Boksburg
Re: Timing belt crank pulley alignement
Panic, I did measure with a ruler. 2mm offset between the 2 pulleys.
Current ride
2007 - Jetta VI 2.0TDI
2007 - Velociti - 2.0 (91wkW, 174nm) @ 8V Performance
2014 - Kia Rio TEC
Previous rides
2008 - Polo 1.9 TDi 14i
2008 - Citi 14i
1996 - Citi Chico
2003 - Ford Fiesta
1986 - Golf MK2
2007 - Jetta VI 2.0TDI
2007 - Velociti - 2.0 (91wkW, 174nm) @ 8V Performance
2014 - Kia Rio TEC
Previous rides
2008 - Polo 1.9 TDi 14i
2008 - Citi 14i
1996 - Citi Chico
2003 - Ford Fiesta
1986 - Golf MK2
- panic-mechanic
- Panic's Place
- Posts: 26715
- Registered for: 21 years 7 months
- Membership No: 79
- Location: Benoni, putfontein.
Re: Timing belt crank pulley alignement
Ok then confirmed that it's out. That was the question wasn't it?
Stephan van Tonder - Jhb - Putfontein Benoni
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10
Perfect Power dealer. I do dyno tuning.
'05 Audi A6 3.0L TDI Avant
'09 Touareg 3l TDI
'13 VW CC 2l tdi (repair project)
'05 Touareg v10
Perfect Power dealer. I do dyno tuning.
-
- Captain
- Posts: 2716
- Registered for: 16 years 4 months
- Car Make: Audi Quatro, polo Beast and A3
- Car Model: S3, Polo Playa,
- Membership No: missing
- Location: Klerksdorp
Re: Timing belt crank pulley alignement
If 2mm out just space all other pulleys in line or let them resize the crank to suit pulleys
- vandyh
- Cadet
- Posts: 93
- Registered for: 10 years 4 months
- Car Make: VW
- Car Model: Velociti
- Location: Boksburg
Re: Timing belt crank pulley alignement
Ok thank will resize crank
Current ride
2007 - Jetta VI 2.0TDI
2007 - Velociti - 2.0 (91wkW, 174nm) @ 8V Performance
2014 - Kia Rio TEC
Previous rides
2008 - Polo 1.9 TDi 14i
2008 - Citi 14i
1996 - Citi Chico
2003 - Ford Fiesta
1986 - Golf MK2
2007 - Jetta VI 2.0TDI
2007 - Velociti - 2.0 (91wkW, 174nm) @ 8V Performance
2014 - Kia Rio TEC
Previous rides
2008 - Polo 1.9 TDi 14i
2008 - Citi 14i
1996 - Citi Chico
2003 - Ford Fiesta
1986 - Golf MK2